![]() Normally, you should be able to customize your VX Nano settings in SetPoint (Logitech's Mouse and Keyboard Software) on the My Mouse tab. However, if this tab is not visible and SetPoint is not displayed as shown below, you will need to re-install SetPoint. Select Logitech SetPoint from the list of programs displayed.Ĭlick the Change / Remove button and follow the on-screen instructions to uninstall SetPoint.ĭownload and install the latest version of SetPoint from the VX Nano Downloads Page. NOTE: You may need to reboot your system after SetPoint has been installed.Īfter your system restarts, open SetPoint to verify that the My Mouse tab is available. Classic start menu view: Start > Settings >Control Panel > Programs and Features >Ĭlick the Uninstall button highlighted above and follow the on-screen instructions to uninstall SetPoint.Įxit SetPoint by right-clicking on the SetPoint icon in the system tray. ![]() The system tray is located in the bottom right corner of the screen next to your clock. Type %windir% in the Run dialog box (shown below).ĭouble-click on the System32 folder to open it. If the wdf01000.sys file is not present, immediately rename wdf01000.bak back to, you should be able to customize your M310 settings in the Logitech Mouse and Keyboard software (SetPoint) using the My Mouse tab. However, if this tab is not displayed, you will need to re-install SetPoint. On the top side of the SetPoint software window you will see two tabs labeled as My Mouse and My Keyboard. SetPoint with My Mouse and My Keyboard tab: NOTE: M310 is only supported in SetPoint 6.1 or above. Hi u/papalibra, Please refer below: -Launch the software by going to Start > Programs > Logitech > Mouse and Keyboard > Mouse and Keyboard Settings OR you can launch it from the system tray icon also. Classic start menu view: Start > Settings >Control Panel > Add/Remove Programs.Start menu view: Start > Control Panel > Add/Remove Programs.SetPoint without My Mouse and My Keyboard tab: Select Logitech SetPoint from the list of programs displayed (shown below):Ĭlick the Change / Remove button and follow the on-screen instructions to uninstall SetPoint.ĭownload and install the latest version of SetPoint from the M310 Downloads Page. The system tray is located in the bottom right corner of your screen next to your clock: NOTE: You may need to reboot your system after SetPoint has been installed.Īfter your system restarts, open SetPoint to verify that the My Mouse tab is available.Įxit SetPoint by right-clicking on the SetPoint icon in the system tray (shown below. Type %windir% in the Run dialog box (shown below).Choose Run.ĭouble-click on the System32 folder to open it.Choose Run. Rename the file wdf01000.sys to wdf01000.bak. WARNING: Before rebooting, check if the wdf01000.sys file is present. ![]() Rebooting without this file may prevent some of your hardware, including mice and keyboards, from working properly. Start menu view: Start > Control Panel > Uninstall a program.If the wdf01000.sys file is not present, immediately rename wdf01000.bak back to wdf01000.sys. Classic start menu view: Start > Settings >Control Panel > Programs and Features. Select Logitech SetPoint from the list of programs displayed as shown below:Ĭlick the Uninstall button highlighted above and follow the on-screen instructions to uninstall SetPoint. My final attempt has been to update the bios (clutching at straws) however another problem, the ASUS update says no asus motherboard detected when I try to install.Īny ideas as to what is wrong would be most appreciated.If the above solutions do not resolve your problem, consult NOTE:You may need to reboot your system after SetPoint has been installed.Īfter your system restarts, open SetPoint to verify that the My Mouse and My Keyboard tabs are available. ![]() I have also tried to the keyboard and mouse on my gaming laptop and it works perfectly. I have AMD 64 FX57 with 2GB corsair ram and A8N-sli premium (the top spec gaming pc from overcockers in November). Its as if the driver is not loaded correctly on plugin/reboot and the only option is to move to a new usb port to install drivers again. If I insert the usb into a another slot (not the same) the hardware is detected again and software installed and all once again works. However if I reboot or unplug and replug in the usb for both devices the lcd and mode buttons no longer work on the keyboard (logitech logo shown on LCD) and the My Mouse option in setpoint is gone. The LCD on the keyboard works fine and the G7 is detected in setpoint. On plugging in usb devices the hardware is found and drivers installed as expected. Installed all the latest drivers being sure to follow install guide to the letter. I have just purchased a G15 logitech keyboard abd G7 mouse. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |